-
产品型号 280 凝固形态/填充剂 半软性/未充填 温度等级 F 产品说明 温度稳定性优良,电气性能及耐热震性良好 A与B的混合比率 重量2:3
体积(%)37:63粘度[1] 25℃(77F)
(以厘米为单位)A=12500
B=2500
混合后4000固化程序[2]
(温度/时间)75℃ (167F) 24小时
95℃ (203F) 6-8小时
120℃ (248F) 2-3小时凝固时间[3]
[温度为60℃(140F)绝缘树脂凝固所需要的时间]20分钟 硬度[4] 73 巴氏硬度
D级比重[5](固化后) 1.08 耐热震性[6]
(通过10个特定温度循环及插入尺寸)130℃至-65℃ 插入为1/8英寸 线性热膨胀[7]
(长度/单位长度/摄氏度数)21*10^-5 抗长强度[8]
(磅/平方英寸)1950 导热性[7]
(cal/秒/平方厘米/摄氏度数/厘米)5.23*10^-4 吸湿量[9][12]
(于相对湿度为96%的环境中存放24小时后所吸取的水分百分率)0.52 介电强度[10]
(采用厚1/8英寸的样本时每ml的电压)375 体积电阻[11]
(于23℃时,每厘米的欧姆值)10^15 颜色 透明琥珀色 -
产品型号 281/5166 凝固形态/填充剂 半软性/已充填 温度等级 F 产品说明 #281及#5166为已填充绝缘树脂,性能与#280大致相同 但#281及#5166的缩减率较低,耐热性及耐机械冲击能力较佳,而且导热性亦较高 A与B的混合比率 重量2:3
体积(%)37:63粘度[1] 25℃(77F)
(以厘米为单位)A=12500
B=25000
混合后48000固化程序[2]
(温度/时间)75℃ (167F) 24小时
95℃ (203F) 6-8小时
120℃ (248F) 2-3小时凝固时间[3]
[温度为60℃(140F)绝缘树脂凝固所需要的时间]21分钟 硬度[4] 73 巴氏硬度
D级比重[5](固化后) 1.43 耐热震性[6]
(通过10个特定温度循环及插入尺寸)130℃至-65℃ 插入为1/4英寸 线性热膨胀[7]
(长度/单位长度/摄氏度数)15*10^-5 抗长强度[8]
(磅/平方英寸)2100 导热性[7]
(cal/秒/平方厘米/摄氏度数/厘米)12*10^-4 吸湿量[9][12]
(于相对湿度为96%的环境中存放24小时后所吸取的水分百分率)0.32 介电强度[10]
(采用厚1/8英寸的样本时每ml的电压)375 体积电阻[11]
(于23℃时,每厘米的欧姆值)10^15 颜色 281 米色
5166 黑色 -
产品型号 9 凝固形态/填充剂 半软性/已充填 温度等级 B 产品说明 3M Electrical Resin 9 is an easy-to-use resin system possessing medium viscosity and unique handling properties. It has a simple 1:1 mix ratio (by weight), a low toxicity potential and is frequently used in applications requiring excellent thermal shock and mechanical shock resistance. The resin’s low exotherm and good pot life allow the user to mix substantial quantities at one time. High adhesion, low stress and low exotherm also reduce the effect of strain and temperature on sensitive components that have been coated with this resin. A与B的混合比率 重量1:1
体积(%)47:53粘度[1] 25℃(77F)
(以厘米为单位)A = 90000 cps
B = 20000 cps
Mixed = 28000 cps固化程序[2]
(温度/时间)23℃ (73F) 24-48 hrs
60℃ (140F) 2 hrs
95℃ (203F) 1 hr凝固时间[3]
[温度为60℃(140F)绝缘树脂凝固所需要的时间]28分钟 硬度[4] 70 巴氏硬度
D级比重[5](固化后) 1.42 耐热震性[6]
(通过10个特定温度循环及插入尺寸)10周期
130℃至-55℃ 插入为1/4英寸线性热膨胀[7]
(长度/单位长度/摄氏度数)13*10^-5 抗长强度[8]
(磅/平方英寸)2200 导热性[7]
(cal/秒/平方厘米/摄氏度数/厘米)7.4*10^-4 吸湿量[9][12]
(于相对湿度为96%的环境中存放24小时后所吸取的水分百分率)0.8 介电强度[10]
(采用厚1/8英寸的样本时每ml的电压)350 体积电阻[11]
(于23℃时,每厘米的欧姆值)10^13 颜色 棕色 -
产品型号 2216 B/A Translucent 凝固形态/填充剂 / 温度等级 / 产品说明 3M™ Scotch-Weld™ Epoxy Adhesive 2216 B/A is a flexible, two-part, room temperature curing epoxy with high peel and shear strength. Scotch-Weld epoxy adhesive 2216 B/A is identical to 3M™ Scotch-Weld™ Epoxy Adhesive EC-2216 B/A in chemical composition. Scotch-Weld epoxy adhesive EC-2216 B/A has been labeled, packaged, tested, and certified for aircraft and aerospace applications. Scotch-Weld epoxy adhesive 2216 B/A may be used for aircraft and aerospace applications if proper Certificates of Test have been issued and material meets all aircraft manufacturer’s specification requirements. A与B的混合比率 重量1:1
体积(%)1:1粘度[1] 25℃(77F)
(以厘米为单位)Base:11000 - 15000
Accelerator:5000 - 9000
混合后固化程序[2]
(温度/时间)100 g Mass @ 75°F (24°C) 2小时 凝固时间[3]
[温度为60℃(140F)绝缘树脂凝固所需要的时间]12-16 hrs. 硬度[4] 73 巴氏硬度
D级比重[5](固化后) 1.08 耐热震性[6]
(通过10个特定温度循环及插入尺寸)130℃至-65℃ 插入为1/8英寸 线性热膨胀[7]
(长度/单位长度/摄氏度数)21*10^-5 抗长强度[8]
(磅/平方英寸)1950 导热性[7]
(cal/秒/平方厘米/摄氏度数/厘米)5.23*10^-4 吸湿量[9][12]
(于相对湿度为96%的环境中存放24小时后所吸取的水分百分率)0.52 介电强度[10]
(采用厚1/8英寸的样本时每ml的电压)375 体积电阻[11]
(于23℃时,每厘米的欧姆值)10^15 颜色 Base:Translucent
Accelerator:Amber
说明 |
|